Cti-products EXB-232 Asynchronous Serial System Extender User Manual

68-11089-115Monitoring and Control NetworkExtender Module (EXB)User DocumentationS2-60596-115CTI Products, Inc.1211 West Sharon RoadCincinnati, Ohio 4

68-11089-11562. The EXB UnitThe EXB unit contains user accessible connectors, indicators and controls to allow efficient useof the EXB module. This s

68-11089-1157"RESET" pushbutton -- Hardware reset for the entire EXB-TELCO module. Non-volatileinformation is retained."CMD" push

68-11089-11582.2 The EXB-Serial UnitThe EXB-Serial unit contains user accessible connectors, indicators and controls to allowefficient use of the modu

68-11089-1159"CMD" button -- currently not used."OPTION A" switches -- 1-4 Reserved. All switches must be UP. 5 No

68-11089-115102.2.1 OPTION B SwitchesOPTION B switches set the Serial Port Handshaking options.1. PORT 1 CTS sense...Disabled E

68-11089-115113. EXB Module SetupThe EXB module requires minimal setup for ease of installation. This section details setuprequirements for mounting,

68-11089-115123.2.4 EXB-TELCO Handset ConnectionA standard telephone handset or other audio input and output device may be connected to the"AUDIO

68-11089-115133.3 Controls3.3.1 EXB-TELCO ControlsThe 8 position DIP switch labeled "OPTION A" provides for EXB module static configuration.

68-11089-115143.3.2 EXB-Serial ControlsThe front panel "OPTION A" switches as well as the rear panel “OPTION B”, “BAUDn” and“MODEn” switches

68-11089-11515RS-232 Hardware Handshake ControlsThe EXB-Serial module uses the hardware handshake control lines to control the flow of data toand from

68-11089-115Standard Limited Hardware WarrantyLIMITED WARRANTY. Equipment manufactured by CTI Products, Inc. is warranted to be free from defects in

68-11089-115164. EXB Module UsageOnce properly connected and configured for use, the EXB module is simple to operate. Run-time operation of the EXB

68-11089-11517Appendix A EXB Module ConnectorsDC IN ConnectorConnector type: 2.5 x 5.5 mm coaxialMating Connector: Switchcraft 760 or equivalen

68-11089-11518building 1 is powering 2 module loads for each IIB plus 2 module loads for the EXB for a total of4 module loads on the power supply. If

68-11089-11519EXB-TELCO Module LINE ConnectorConnector type: standard RJ11 telephone style, 6 position 4 contact.For 2 wire leased-line operation, con

68-11089-11520EXB-Serial Module PORT 1 and PORT 2 ConnectorsConnector type: standard DE9 malePinout as DTE (PC-AT pinout)In general, all signals (exc

68-11089-11521Appendix B EXB Module SpecificationsDC Power Input: 10 to 30 VDC, unregulatedInput Power:5 watts maximum - this counts as two MCN

68-11089-11522Appendix C EXB Mounting OptionsWall mount and EIA 19” rack mount kits are available as options for the EXB from CTIProducts, Inc.

68-11089-11523Rack Mount OptionThe rack mount option allows up to three EXB modules to be mounted in a one rack unit height(1.75 inches) of a standard

68-11089-11524To attach a module to the rack adapter, and then mount the rack adapter into therack, follow the steps below.WARNINGDo not allow the PC

68-11089-11525Appendix D Application NotesUsing the EXB-TELCO Module with Motorola STARPLEX Microwave SystemThis application note describes how

68-11089-115iTable of Contents1. INTRODUCTION...

68-11089-11526EXB Module Phone Line Level SettingTransmit: If you are using standard STARPLEX modems and terminations, set the transmitlevel on the EX

68-11089-11527Appendix E FCC Notices1. The Federal Communications Commission (FCC) has established Rules which permit this device to be directl

68-11089-115iiManual RevisionsRev. Date Description110 Original Release115 10/12/2002 Added extended baud rate table, Option B switch description (RS

68-11089-11511. IntroductionThe Extender Module (EXB) is used in pairs to connect multiple MCN modules in real-time,spanning distances from building-w

68-11089-1152The second type of EXB module is the EXB-Serial Module. This module interfaces with avirtual RS-232 communications channel (such as a hi

68-11089-11531.2 EXB Communication Channel InterfacesThis section describes the communication channel interface of the EXB-TELCO module and theEXB-Ser

68-11089-11541.2.2 EXB-Serial Communication Channel InterfacePORT 1 and PORT 2 are standard asynchronous serial ports with individually configurable b

68-11089-1155COM 2COM 1PORT 1PORT 1SERIAL SERIALCA-80304-100PORT 1SERIALPORT 2CIBHIBTINOUTOUTTCIBOUTTLOCAL PCT1MUXT1MUXT1MUXT1MUXCIBOUTINCIBOUTININCOM